Skip to Content

Tag Archive: tooling solutions

  1. Spoil Boards, Hold-downs, and Dust Collection

    Comments Off on Spoil Boards, Hold-downs, and Dust Collection

    Holding the part to be cut firmly and without movement or vibration is often the biggest challenge faced when cutting on a CNC. Chatter, movement, premature tool wear, tool breakage, poor edge finish, and chipping are the result of inadequate hold-down. How well you can hold the part is perhaps the biggest factor in how fast you can cut.

    There is a lot of information on building dedicated spoil boards and jigs so we cover the basics in our free downloadable CNC Manual, and will provide an excerpt here. For the rest of the article, refer to the CNC Manual pages 13, 14, 15.

    Some factors to consider include:

    • Some CNC operations are best suited to using flow through or suck through vacuum systems. Particularly well-suited for cutting large parts and sheets of material, these types of routers utilize replaceable spoil boards—so called because they are underneath the material to be cut and are cut and “spoiled” during machining. The spoil board can then be resurfaced and used again, sparing the router table underneath from damage. These types of systems are easy to use and require minimal maintenance. Using low (LDF) or medium density fiberboard (MDF), both sides are machined level using a large “fly” cutter to remove any imperfections or coatings. Vacuum is evenly distributed to the entire surface of the table. Air loss from the sides can be minimized by using rubberized or latex paint. Areas not to be used should be sealed with sheets of laminate, plastic, or other non-porous materials. Grooves resulting from the cutting process can cause vacuum leakage when cutting a variety of patterns. Resurfacing the spoil board should be done regularly.

    • Smaller or more intricate parts are better suited to dedicated spoil boards due to vibrations and part movements. Cutting small parts can be challenging since a larger volume of air is lost due to the number of channels cut between parts. As more parts are cut, more air pressure is lost, resulting in vibration and part movement.

    • Leaving a thin skin (onion skin) or programming tabs at certain points can help to hold small parts together but require a secondary routing or sanding operation.

    • Use dedicated spoil boards for recurring part runs. Taking the time to make a proper spoil board will pay for itself by allowing faster feed rates, giving you a better finish, and prolonging tool life.

    To continue, refer to the CNC Manual pages 13, 14, 15.

  2. Custom CT & HSS Tooling: EOASAW Can Help!

    Comments Off on Custom CT & HSS Tooling: EOASAW Can Help!

    Can’t find a stock tool for your cutting situation? Edge of Arlington can help you with a unique cutting solution tailored to your particular needs. We are experienced in a wide variety of materials, applications, and processes. We have on-site manufacturing capabilities and represent some of the finest industrial manufacturers in the world.

    Purchasing custom tooling doesn’t have to be complicated, intimidating, or mysterious. It is really a simple matter when broken down in steps:

    1) Gather information

    The more information we have to work with, the better. Many times the type of tool that we will design will be dictated by the machinery to be used, material to be cut, ability to hold the material, etc.

    2) Supply profile to be cut

    Please supply a wood sample, dimensional drawing or .DFX file of the profile to be cut. If the profile is too large it may be necessary to break up the cut, utilizing multiple tools.

    3) Drawing approval

    Once we have all the information and your profile, we will supply a detailed print for your final approval. Please make sure that you verify the information closely as custom tooling is not returnable after approval. The print will have a unique identifying number for easy re-ordering and will include details, such as tool rotation and orientation.

    4) Tool delivery

    Delivery of custom tooling can vary greatly from a few days to many weeks. Some processes, such as heat treatment or grinding diamond, cannot be sped up. We try to work with our customers to deliver in the time frame needed. We have on many occasions performed near miracles, such as overnight delivery; however, that can come at great cost and is not always possible.

    There are too many cutting situations to try to cover all possibilities. Please fill out the request for quote form with your contact information and as much other information as you can supply. We will contact you and ask specific questions as needed.

    Examples of basic information can be found on our Custom CT & HSS Tooling Page.

  3. Edge of Arlington Featured on Inside The Blueprint Local Edition

    Comments Off on Edge of Arlington Featured on Inside The Blueprint Local Edition

    Edge of Arlington Saw & Tool  is featured on Inside The Blueprint.

    Join us as they go behind the scenes for innovations in healthcare, design-build manufacturing, and, of course, Edge of Arlington’s segment on tooling and machinery.

    Our EOASAW segment begins at the 4 minute mark.